Cyclone Abrasive Flap Discs MSDS Sheet

MSDS - Cyclone Flap Discs - Glass Fiber Backed

Section 1 - Product Identification
Manufacturer's Name: Anderson Products
Address: 1040 Southbridge Street - Worcester, MA 01610
Emergency Telephone Number: (508) 755-6100
Telephone Number for Information: (508) 755-6100
Date Prepared: January 25, 2006
Name of preparer: Frank J. Hettes

Section 2 - Hazardous Ingredients/Identity Information

Ingredients	OSHA PEL	ACGIH TL
AL2O3 (Aluminum Oxide) ZR O2 (Zirconium Oxide) Epoxy Resin (Based on a blend of Bisphenol-A & Bisphenol-F) CACO3 (Calcium Carbonate) Cotton Glass-Fiber Phenolic Resin	15mg/m3 5mg/m3 N.I. N.I. N.I. N.I. N.I.	15mg/m3 5mg/m3 N.I. N.I. N.I. N.I. N.I.

Section 3 - Physical/Chemical Characteristics
Boiling Point: **N/A
Vapor Pressure (mm Hg.): **N/A
Vapor Density (AIR=1): **N/A
Solubility in Water: The paper label has slight water solubility
Specific Gravity (H2O=1): **N/A
Melting Point: **N/A
Evaporation Rate (Butyl Acetate=1): **N/A
Appearance and Odor: Solid fiberglass disc coated with flaps of abrasive cloth; no odor.

Section 4 - Fire and Explosion Hazard Data
Flash Point (method used): **N/A
Flammable Limits: 200 degrees C LEL: **N/A UEL: **N/A
Extinguishing Media: Any standard extinguishing media (water, carbon dioxide, foam, dry chemical)
Special Fire Fighting Procedures: None
Unusual Fire and Explosion Hazards: None

Section 5 - Reactivity Data
Stability: Stable
Conditions to avoid: **N/A
Incompatibility (Materials to Avoid): **N/A
Hazardous Decomposition or Byproducts: During use, grinding dust is generated.
Hazardous Polymerization: Will not occur

Section 6 - Health Hazard Data

Primary Route(s) of Entry	Health Hazards (Acute and Chronic)	First Aid and Medical Information
Inhalation	May cause coughing, shortness of breath.	Remove to fresh air. Seek medical advice if chronic.
Ingestion	Ingestion very unlikely and not recommended.	Seek medical advice.
Skin	May cause abrasions. Dust may cause skin irritation	Obtain First Aid. Wash with soap and water.
Eyes	Dust may irritate eyes.	Wash with water. Seek medical advice.

Carcinogenicity: Not known

Section 7 - Precautions for Safe Handling and Use
Steps to be taken in case material is released or spilled: No special procedures; standard clean-up.
Waste disposal method: Standard landfill methods consistent with applicable Federal, State and Local laws.
Precautions to be taken in handling and storage: Handle with care, avoid impact; store dry at 20 degreesC+/- 20 C; 55-60% air humidity.
Other Precautions: Normal precautions for nuisance dust and particulates generated during grinding.

Section 8 - Control Measures
Respiratory protection (specify type): Use approved respiratory protection for nuisance dust.
Ventilation:
Local Exhaust: Required
Mechanical (General): Recommended
Special: Respiratory protection
Other: **N/A
Protective gloves: Recommended
Eye protection: Mandatory
Other protective clothing or equipment: Hearing protection & face shield recommended; keep machine guards in place.
Work/Hygienic Practices: **N/A

**N/A = Not Applicable

The information in this MSDS was obtained from sources which we believe are reliable. However, the information is provided without any representation or warranty, express or implied, regarding the accuracy or correctness.

The conditions or methods of handling, storage, use and disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of, or in any way connected with, the handling, storage, use or disposal of the product.

Anderson Products Home
About Us | Products | Literature | MSDS Sheets | Copyright Info