Convolute Wheels MSDS Sheet

MSDS - Convolute Wheels

Section 1 - Product Identification
Manufacturer's Name: Anderson Products - One Weiler Drive - Cresco, PA 18326
Information and Emergency No.: (800) 755-6101
Product Name/Trade Name: Exp - Deburring & Polishing
Common Name/Grade: Convolute
Revised: June 20, 2011
Name of preparer: Frank J. Hettes

Section 2 - Hazardous Ingredients
Note: Products under normal conditions do not represent an inhalation, Ingestion or Contact Health Hazard.

Ingredients	CAS#	Percent	Exposure	Limit Source
Nylon Fibers Phenol-Formaldehyde, Cured Resin Polyurethane Resin, Cured Epoxy Resin, Cured Abrasive Particles	- - - - -	5 - 30 15 - 30 15 - 30 15 - 30 15 - 30	N/A N/A N/A N/A 10 mg/m3	2 2 2 2 1

Note: Products detailed on this MSDS are defined as articles in the federal occupational safety and health administration (OSHA) hazard communication standard. See 29CFR Sec. 1910.1200 (c)

Source of exposure limit: 1 - ACGIH threshold limit value 2 - None Established

(1) % of Alloying Material Varies With Grade of Material. (2) 1985-1986 ACGIH Threshold Limit Value.

Section 3 - Physical Data
Material is (at normal conditions): Resin Bonded Abrasive Particles
Melting Point (Base Metal): N/A
Appearance and Odor: Solid and Odorless
Specific Gravity: Not determined (Water = 1)

Section 4 - Fire and Explosion
Extinguishing Media: Carbon Dioxide, Foam, Water, Dry Chemical
Special Fire Fighting Procedures: N/A
Unusual Fire and Explosion Hazards: N/A

Section 5 - Reactivity Data
Stability: Stable
Conditions to Avoid:
Hazardous Decomposition Products: Exposure to flame; cyanides, carbon monoxide, carbon dioxide, nitrogen oxide
Incompatibility (Materials to Avoid): N/A

Section 6 - Health Hazard Data
Note: Steel products in the natural state do not present an inhalation, Ingestion or contact hazard; however, operations such as burning, welding, sawing, brazing and grinding may release fumes and/or dusts which may present health hazards if TLV'S are exceeded.

Major exposure hazard: N/A all mechanical. Inhalation: Skin Contact: Skin Absorption: Eye Contact: Ingestion:

Effects of Overexposure: Dust may be generated during normal use. To avoid dust inhalation, use appropriate dust mask. Particulate collection system. Use of protective glasses and/or face shield is recommended at all times. (Recommended by ANSI standard Z87.1.)

Emergency and First Aid Procedures:
Eye Contact- Flush with plenty of water. Physician should be contacted if irritation persists.
Skin Contact - Wash with soap and water.
Inhalation - Provide fresh air
Ingestion: Mechanical only

Section 7 - Spill or Leak Procedures
Spill or Leak Procedures: N/A
Waste Disposal Methods: Proper disposal is in approved sanitary landfill

Section 8 - Special Protection
Respiratory: Use of particulate collection system during use is recommended.
Ventilation: Use of particulate collection system during use is recommended.
Eye Protection and Protective Clothing: Use of approved face mask and/or face shield. Spproved dust mask.

Section 9 - Special Precautions
Avoid breathing dust during use. All mechanical.

The information in this MSDS was obtained from sources which we believe are reliable. However, the information is provided without any representation or warranty, express or implied, regarding the accuracy or correctness.

The conditions or methods of handling, storage, use and disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of, or in any way connected with, the handling, storage, use or disposal of the product.

Anderson Products Home
About Us | Products | Literature | MSDS Sheets | Copyright Info